Tubo de salida para bañera - Desviador con tirador hacia arriba en cromado

Hi Tinman, Thank you for your question about the Delta Faucet RP52148SS. This tub spout has a SpotShield stainless finish. A stainless finish will match a SpotShield stainless. Please reach out with any additional questions! Best Regards, Bryan Digital Communications Specialist

Hello GregS, Thank you for your question! I am happy to help you! The Delta Faucet DRYDEN™ Tub Spout - Pull-Up Diverter MODEL#: RP52148 uses the RP12307 adapter, Which can be soldered onto 1/2" copper pipe or threaded onto a 1/2" IPS pipe nipple. This adapter should be soldered between 5/8" – 1 5/8” from the finished wall. Once the adapter is installed the tub spout can be threaded onto the adapter for a tight seal. Thank you for being a loyal Delta customer. Please contact us back for any further questions. Best Regards, Nicole

Thank you for your question. Unfortunately, the plastic adapter is not available as a separate piece. The entire tub spout will have to be replaced. Thanks, Sherry

Hello Josh, Thank you for your question! I am happy to help you! The Delta RP52148 tub spout has a maximum flow rate of 7.0 GPM @ 60 psi, the part at the tip of the spout does not need to be removed. Please contact us back for any further questions. Best Regards, Nicole

Hi Jim M, Thank you for your question about the Delta Faucet RP52148. This tub spout does not use a mesh screen. Please reach out with any additional questions! Best Regards, Bryan Digital Communications Specialist

Hello Patrick! Thank you for your question and we are happy to help. We apologize for this information not being readily available to you. There is no aerator in the Delta DRYDEN™ Tub Spout - Pull-Up Diverter MODEL#: RP52148SS. We recommend soaking the tub spout in a 50% warm water and 50% white vinegar solution. We also recommend flushing the valves of your shower: Turn off the hot and cold supply to the valve. This may involve shutting off the water to the entire residence, or for the room or fixture. [Or there may be supply stops on the valve itself behind the escutcheon requiring removal of the handle.] Turn the volume control on to relieve any pressure behind the valve. Remove the handle, There may also be a trim sleeve to slide off of the valve. If you have supply stops on the valve itself, you will remove the escutcheon plate to access those. Remove the bonnet. A strap wrench works best to not deform the bonnet. Caution: Be careful not to twist the valve. Remove the cartridge by wiggling as you pull, taking care to protect the stem. If the cartridge has a metal stem, reattach the handle to provide a better grip. Check inside the valve for any other components and remove those. Once all the parts have been removed from the valve, close the shower curtain or door. Caution: the water may be very hot. Turn both of the water supply valves on full and let the water run for 60-90 seconds. Perform any maintenance on the removed components. Reassemble the shower valve. Check for leaks. With any further questions or concerns, please do not hesitate to reach out to us directly. Thank you for being a loyal Delta customer. Best Regards, Carrie

Hi JAG2, Thank you for contacting Delta Faucet Company! Please accept our sincere apology for the inconvenience you are experiencing. Here is what we can do to resolve your issue for you. Our Delta Faucet Dryden™ Tub Spout Pull-Up Diverter In Matte Black MODEL#: RP52148BL does not control the flow of water, low flow would be caused by a blockage or debris in the valve. I have included the step-by-step instructions on flushing the rough valve, please see the steps below. To flush the open valve without the cartridge, please follow the directions below. 1) Remove the handle, I have included a how-to video link below to show how the different shower handles are removed. https://www.youtube.com/watch?v=QGjEgAUHX8c 2) After removing the handle, remove the trim sleeve. 3) Then you will need to remove the bonnet nut. The bonnet nut is the threaded ring at the valve opening. It unscrews counterclockwise. You will need a pipe wrench or a pair of channel locks. 4) After removing the bonnet nut, you will need to pull the cartridge straight out. You may need a small, skinny bladed screwdriver to wedge in between the lip of the cartridge and the valve to help start it out. 5) Once the cartridge is removed, you will have an open valve body. 6) Next, shut the shower door or curtain and turn the water on to the valve. Water should gush out, much like an open fire hydrant. Have someone observe if there is good water pressure coming out of the valve and let it flush for 30 seconds. 7) Re-install the cartridge and re-assemble in reverse of how it was disassembled. The Tub/Shower should then have a good flow. Thank you for being a loyal Delta Faucet customer. We appreciate your business and look forward to continuing to serve you. Please contact us back with any further questions. Best Regards, Nicole

Hi Sandro, Thank you for your question regarding our Delta Faucet RP52148CZ. is made of non-metallic material. Non-metallic products are beneficial in that they do not rust or corrode and help prevent heat transfer. We also have a Lifetime Limited Warranty on all parts and finish. Your feedback is important to us, as it helps us refine our products and services. Feel free to contact us directly, so we can further assist you with this matter. Thank you for being a loyal Delta Faucet customer. Best Regards, Themar Digital Communications Specialist (800) 345-3358 customerservice@deltafaucet.com

Hello Rosie, Thank you for contacting us, I would be happy to help you. Our Delta RP52148SS is made of non-metallic material. Non-metallic products are beneficial in that they do not rust or corrode and help prevent heat transfer. We also have a Lifetime Limited Warranty on all parts and finish. Your feedback is important to us, as it helps us refine our products and services. Feel free to contact us directly, so we can further assist you with this matter. Best Regards, Nicole

Hi James, Thank you for contacting Delta Faucet. Please accept our sincere apology for the inconvenience you are experiencing. We will be happy to assist you in resolving this issue as quickly as possible. Our Delta Faucet Delta DRYDEN™ Tub Spout - Pull-Up Diverter In Chrome MODEL#: RP52148 uses the RP12307 adapter, Which can be soldered onto 1/2" copper pipe or threaded onto a 1/2" IPS pipe nipple. This adapter s is installed the tub spout can be threaded onto the adapter for a tight seal. Thank you for being a loyal Delta Faucet customer. Please feel free to call, email, or message us on social if you need anything else. Best Regards, Themar Digital Communications Specialist