Retén del tubo de salida

Hello, Thank you for your question! First you will slide the decorative spout bonnet up to reveal the RP21463 retainer. Next, you will firmly pull upward on the spout until it is removed from the valve. You can then remove the existing retainer and put the new one in place. You will put one of the "teeth" of the retainer in the hole in the spout for a secure connection. Please reach out with further questions! Best Regards, Tim Digital Communications Specialist

Hi Nick, Thank you for your question. To remove the RP21463 spout retainer you will want to press down on the retainer and slowly pry apart the bottom of the retainer to release the part from the faucet. Thanks, Dave

I just experienced the same frustration with the tapered neck on the bonnet. The solution came from my son when he suggested using duck tape. So I wrapped several 1" strips on the upper part of the neck in order to make it approximately the same diameter as the rest of the bonnet. That gave me enough surface area for the strap wrench to get a good even grip, and after some serious torque the bonnet finally broke free! From there it was all downhill and after replacing the O rings my faucet is now leak free.

Hi Henry, Thank you for your question. Delta Faucet model # RP21463 is a spout retainer that will fit inside the spout. Thanks. Jody

Hi Joe, Thank you for your question. If there is no damage to the RP21463, the spout retainer it can be reused. Thanks, Dave

Hello Rusi, Thank you for your question! I am happy to help you! Our Delta RP21463 can be removed by taking the smaller bonnet located at the bottom of the spout and sliding it straight up. After sliding the bonnet up to reveal the spout retainer, you can then pull the retainer open slightly and slide it up the spout. Lastly take the new retainer and slide it back down the spout to snap in place. Please contact us back for any further questions. Best Regards, Nicole

Hi Chief1956, Thank you for your question! For a Delta Faucet model 9192-DST & 9992-DST a replacement friction spacer is RP62875. Unfortunately, this part is discontinued. Please reach out with any additional questions! Best Regards, Bryan Digital Communications Specialist

Hi Bob B, Thank you for contacting Delta Faucet Company! Please accept our sincere apology for the inconvenience you are experiencing. Here is what we can do to resolve your issue for you. I have included step-by-step instructions for our Delta Faucet Spout Retainer MODEL#: RP21463 removal and installation. First, start by turning off both hot and cold water, then turn the handle on and in a mixed position to drain any leftover water. Next unthread the bonnet(collar) from the base of the spout, if tight you can soak a rag in 50/50 white vinegar and water and wrap around the bonnet for 5-10 minutes. Once loose, slide it up to find the spout retainer. There should be two tabs, one on each side of the retainer. Pull the tabs out of the spout body and slide the retainer up. Lastly, swivel the spout side to side and pull off the spout. We would also recommend cleaning the faucet body and spout with the 50/50 solution before reinstalling. Thank you for being a loyal Delta Faucet customer. We appreciate your business and look forward to continuing to serve you. Please contact us back with any further questions. Best Regards, Nicole

Hello David, Thank you for contacting Delta Faucet Company! I am sorry this information was not readily available about the Delta Faucet Spout Retainer MODEL#: RP21463; however, I am happy to help you. I have attached a link below to the Where To Buy section on our website. https://www.deltafaucet.com/where-to-buy Our products have a Lifetime Limited Warranty that covers parts and finishes being free of defects in material and workmanship for the original owner/purchaser. Please feel free to contact us with any questions or for further assistance. Thank you for being a loyal Delta Faucet customer. Best Regards, Emma

Hi Richard, Thank you for your question about the Delta Faucet RP21463 Spout Retainer. I am sorry this information was not readily available, and I am happy to help! 2174, 2176, 2474, and 2476 Series faucets use the RP22934 o-rings. https://www.deltafaucet.com/parts/product/RP22934.html See the part diagram for more information. https://media.deltafaucet.com/PartsDiagram/2100_2102_2400_2402_70700_Rev_A.pdf Please contact us directly if you have any questions or need additional assistance. Thank you for being a loyal Delta Faucet customer. We appreciate your business and look forward to continuing to serve you! Best Regards, Bryan Digital Communications Specialist

Hi mark6133, thank you for your interest in the RP21463! The RP21463 is not compatible with Delta Faucet 187. The replacement retainer is RP37022. Please view the part in the link below. https://www.deltafaucet.com/parts/product/RP37022.html?utm=delta Please contact us directly if you have any questions or need additional assistance. Best Regards, Themar Digital Communications Specialist

Hello no diagram to see! Thanks for the questions. Below is diagram showing where the o-rings are located. https://media.deltafaucet.com/PartsDiagram/Models_172_174_RevB.pdf Please contact us back if you have any questions or need further assistance. Best Regards, Paul