Delta®
Cubierta - Series 600/1600 (ducha y bañera) en cromado
N.º de modelo: RP5883
Image Thumbnail, click to view zoomed product image 
Documentos y especificaciones
Información de instalación
Altura total:
3/4
Voltaje:
0
Tipo de válvula:
NA
RESEÑAS
Rated 5 out of
5
by
mam20973 from
Replacement Trim
I was happy to find the old style trim for replacement. It fit well and worked out perfectly.
Date published: 2018-02-05
Rated 4 out of
5
by
GS_60605 from
Escutcheon for Delta 600 series shower tap
Difficult to get out of packaging. Replacement part works.
Date published: 2015-10-06
Rated 1 out of
5
by
Joe from
I Had to return it.
I had to return it because in the picture it shows a center hole for the diverter but there was none. Further research with Delta revealed that it is no longer made, etc.
Date published: 2015-01-12
Rated 1 out of
5
by
knotagain from
Wrong escutcheon
Second complaint on this item on the site-picture displays the wrong escutcheon. Shows diverted hole but this model doesn't have one.
Date published: 2013-04-23
Rated 5 out of
5
by
cg108 from
Bath Glistens Again!
Perfect replacement! Bath fixtures look new again!
Date published: 2009-06-30
Rated 1 out of
5
by
amateurhomeimprover from
Not as pictured
the pictured item shows this product for use with a diverter, the item shipped however was not as pictured and could not be used with a diverter faucet.
Date published: 2009-02-07
Preguntas y respuestas
Are the screw holes at a 5 - 7 o'clock position?
Hi Debby, Thank you for your question. The screw holes on the 600 Series Escutcheon are at the 5 & 7 o'clock positions.
Thanks,
Dave
Date published: 2024-03-28
Does this escutcheon come with screws and the two gaskets? Thanks
Screws have to be ordered separately. Delta gave me part number RP196 for the chrome screws (I haven't received them yet to confirm they are the right ones). The escutcheon has two gaskets attached to it, one for the smaller diameter inner hole and a piece of foam for the inside of the outer edge. Good luck!
Date published: 2024-03-28
What is the internal diamer of the hole? Thank you
Thank you for your question, George76! The diameter of the internal hole is 1 3/4".
Best regards, Edward
Date published: 2024-03-28
Is this piece flat?
If you were to set it on a flat surface, while the inner ring where the screw holes are located touches the surface, would the outer circumference be touching the surface also? In other words, is the inner ring lower/deeper?
My experience is inconsistent with the reply you received from Brandis at Delta. I was also told the same thing by Delta when I called them last week. When I explained what follows below to the person on the phone, they were unable to understand me. I had previously ordered the chrome RP5883 escutcheon to replace an old gold one (part number unknown-Delta really should put part numbers on their parts it would save a lot of hand waving over the phone). I actually ordered RP5883 twice by mistake from different sources; the parts I received were the same.
> Photo A: You can see the outer edge of old goldie is above the counter surface while the edge of the inner opening rests on the counter. Both the inner and outer edges of the new chrome one would be flush with the surface if the foam gasket behind the outer rim were not there. But if you look closely, you can still tell the chrome one sits lower than the gold one.
> Photo B: Edge view.
> Photo C: Undersides.
I am now ordering RP7577, confusingly described by Delta as the "shallow" version of this escutcheon, which might be the one I need. Or I might just spray paint the whole shower a nice shade of brown.
Date published: 2024-03-28
Do you have the shower handle that is compatible with the RP1991 faucet cartridge? Which one is it?
Hello Luis512,
Thank you for your question! I am happy to assist you!
The Delta RP1991 cartridge has a stem unit that is shaped to fit the 1600 series and 1300/1400/13/14 series shower handles. A common 13/14 series handle kit to use is H74 with the A74 accent.
Please contact us back with any further questions.
Best Regards,
Skyler
Date published: 2024-03-28
what is the outside diameter?
Hello john,
Thank you for your question.
The escutcheon is 6 3/4" in diameter.
Please contact us back if you have with any further questions.
Best Regards,
Emma
Phone: (800) 345-3358 | Email: customerservice@deltafaucet.com
Date published: 2024-03-28
How do I identify the model/part number? I have a Delta from 1972 when the house was built. I need the escutcheon. The brass casting in the wall has 249 stamped on the upper left next to the 'up' . It would need a center hole of 1.8 "
What is the depth of the Escutcheon?
Hello Jeremy,
Thank you for your question! I am happy to help you!
Our Delta Faucet escutcheon plate RP5883 has a depth of .55.
Please contact us back for any further questions.
Best Regards,
Nicole
Date published: 2024-03-28
Precios de Delta en línea
Este precio en línea es exclusivo de DeltaFaucet.com. El precio de lista puede aparecer en productos ofrecidos fuera de la sección de la tienda outlet en DeltaFaucet.com. Pueden usarse precios tachados para mostrar descuentos.