Llave para cocina extensible de una manija con tecnología ShieldSpray® en Champagne Bronze

Hi, Cheryl! Thank you for your question. The Delta 9178-DST Faucet sprayer assembly can be removed from the hose assembly and cleaned by soaking the whole sprayer in a solution of 50% white vinegar and 50% water mix for an hour or even overnight. Best Regards, Rosanna

Thank you for your question, Bonnie! The Delta model 9178-DST does have a removable aerator however it will require the aerator wrench that was supplied with the faucet. Please see the part diagram below for reference. https://media.deltafaucet.com/PartsDiagram/DPD-K-9178-DST.pdf Best regards, Edward

Hi, GGGA! Thank you for your question. The Delta 9178-AR-DST Faucet swivels 360 degrees at the high arc spout. The handle turns on and away from the faucet for cold and the handle turns back for hot water. We recommend a minimum 2 1/2" (64 mm) clearance to back splash. Best Regards, Rosanna

Hi Charlotte, Thank you for your question. To adjust the Handle Limit Stop, remove the red/blue button, loosen the set screw with an 1/8" Allen wrench, and pull off the handle. The red switch on the top of the cartridge can be flipped to the right to limit the range of the handle on the hot side. While this can be done without turning off the water supply, we recommend to turn them before disassembling the faucet. Best regards, Jon

Hi Alevine, Thank you for your question. The Artic stainless finish will have a blue tint to it, while the stainless steel will have a gold tint. Both finishes are durable and warrantied for the life of the faucet to the original purchaser. The faucets are finished in stainless steel, not made of stainless. Thanks, Dave

Hi, Homeowner! Thank you for your question. The Delta 9178-AR-DST Faucet sprayer is available as a replaceable part. The part number is RP90841. Here is a link to the part: https://www.deltafaucet.com/parts-product-detail?modelNumber=RP90841 Best Regards, Rosanna

Thank you for your question, GGGA! You should only have to press the button on the wand once. The wand will stay in spray mode, until the button has been released. Best Regards, Benjamin

Hi, Ricardo. Thank you for your question. The Delta 9178T-SP-DST Faucet requires a hole size of 1 3/8"(35 mm). Here is a link to the technical specifications sheet for further measurements: https://media.deltafaucet.com/SpecSheet/DSP-K-9178T-DST_C.pdf Best Regards, Rosanna

Thank you for your question, williedrip! All necessary dimensions and measurements needed for installation can be found on the Technical Specifications Sheet below. https://media.deltafaucet.com/SpecSheet/dsp-k-19978-sd-dst_D.pdf Best regards, Edward

The Leland faucet has a selector switch for aerated spray or full...and the spray isn't a wide spray meaning it's very controlable even when not pulled out of the magnetic base. Included in the box is a tool for removing the aerator portion for cleaning of calcium/lime deposits. Suggest using vinegar for the disolving of these deposits and not a "lime away" type chemical. I don't know if the finish would be harmed by the "lime away" product but I'm not willing to experiment.

Thank you for your question. Delta Faucet model # 9178-SS-DST has a spout that reaches out into the sink 9-13/64" so it is your preference if you think it will look right on the sink. It will function. We have included the spec sheet below for your information. http://www.deltafaucet.com/customersupport/documentation/9178-ss-dst.html?document=ts&documentIndex=0#flashWrapper

Hi, Pat S! Thank you for your question. The Delta soap dispenser for the 9178-SP-DST has a hole size requirement of 1 3/8" (35 mm). Best Regards, Rosanna

Thank you for your inquiry, Suez! The Delta Leland Pull-Down Kitchen 9178-DST model comes with a 62" pull-out hose assembly. Best regards, Tanya

Hello Richard, Thank you for your question. The wand/sprayer assembly of the Delta Leland Pull-Down Kitchen 9178-DST faucet can be removed, simply by unscrewing it from the pull-out hose assembly. Please feel free to call, email, or message us on social if there is anything else you need. Best regards, Tanya Phone: 1-800-345-3358 | Email: customerservice@deltafaucet.com | Facebook/Twitter: @deltafaucet

Hello Linda, Thank you for your inquiry! There are no know issues with the spout retainer of the Delta Leland Pull-Down Kitchen 9178-SP-DST faucet model. We're always striving to make our faucets and products better and update our parts as needed. Please know that all of our products undergo rigorous tests to ensure long-lasting use and are made with high-grade materials. If you're having issues with your faucet, please contact us via email at customerservice@deltafaucet.com or you can also call the toll-free Delta Help Line at 1-800-345-3358 between the hours of 7:00 AM to 7:00 PM Monday ~ Friday as well as 8:00 AM to 5:00 PM Saturday CST. Best regards, Tanya

Thank you for your question, thearcher01! Model 9178-AR-DST and all of our faucets are manufactured in our plant facilities in Greensburg, Indiana; Jackson, Tennessee; London, Ontario, CA; and Panyu, China. As a global manufacturer, we also source and assemble a number of parts around the world. No matter where in the world our products are sourced, manufactured or assembled, they are built to Delta Faucet Company’s exacting specifications and are quality tested to ensure long-lasting performance. Best Regards, Benjamin

Hi ls_5chevelle, Thank you for your question! This is the RP40530 hose guide. It is used to assist in the installation of the hose to keep it from catching. Simply insert it into the end of the hose, slide the hose through the faucet, then remove the guide. Best regards, Jon

Dear Eugenia512, Thank you for your question. The Hose assembly of the Delta Leland Kitchen Pull-Down 9178-DST faucet, is design as self retracting. You would need to push the wand back up towards the spout assembly. The faucet does have a MagnaTite docking wand/sprayer assembly. There is a magnet on the top side of the sprayer and another one inside the end of the spout, that locked together to hold the sprayer in place. Best regards, Tanya

Thank you for your question, John! We do no recommend lubricating any parts of a Delta faucet unless instructed to do so. The noise you are hearing may be caused by a damaged friction spacer, part number RP60923. For further assistance with this part, please contact us directly. https://www.deltafaucet.com/parts-product-detail?modelNumber=RP60923 Best regards, Edward

HI, BufordTJustice! Thank you for your question. Our faucets are made of several materials, Unfortunately, I am unable to provide a specific breakdown for your faucet as that information is considered proprietary. But in general, our faucets may contain: Bronze Brass (36000, 260) (hub, handle, body, tube, fittings) Zinc (escutcheon, hub, handle) Stainless Steel (undercover plate, seat liner, set screw) Copper (tubing) PEX-C (puck and tubing) Silicone (gaskets) Synthetic rubber - EDPM, Santoprene (hoses) Vinyl (hoses) Nylon Plastics I am sorry the information you were looking for was not readily available for you. Please know that all of our products undergo rigorous tests to ensure long-lasting use and are made with high-grade materials. Best Regards, Rosanna

Thank you for your question, Caja! The threaded shank of the Delta Leland Pull-Down Kitchen 9178-AR-DST model is brass. Best regards, Tanya

Hi didibaby, Thank you for your question. The hose is 54" in length and will provide approximately 22" of reach from the end of the spout. Best regards, Jon

Dear Aclmark, Thank you for your question. Delta does not recommend and advises that no polishes or coatings should be used on any of our finishes. The cleaning care directions from the warranty states: Always blot dry any water from faucet surface. Allowing water to evaporate on the surface can lead to build up of mineral deposits. Cleaning with a damp non-abrasive sponge and buffing it dry with a clean soft cloth should help keep your product looking beautiful. To remove water spots, use warm water and a soft, damp cloth. Hard water stains may be removed using a 50/50 solution of white vinegar and water. Make certain that you rinse thoroughly with water afterward. If additional cleaning is required, all of our finishes may be cleaned with the following household cleaners: Formula 409® Antibacterial All Purpose Cleaner, Fantastik® All Purpose Cleaner, or Windex® Original Glass Cleaner, when used according to the manufacturers' instructions for use. Avoid using the following which can damage your finish: Avoid industrial cleaners and abrasive cleaners, such as those used for toilet bowls, green Scotch-Brite heavy duty scrub sponges, Scrubbing Bubbles Bathroom Cleaner and Lysol Basin Tub, Soft Scrub, and Tile Cleaner. Avoid products that state on the label that they remove tarnish and rust, and those containing hydrofluoric, hydrochloric and/or phosphoric acids and caustic agents. Avoid harsh abrasives, coatings and/or polishes. Avoid bleach-based cleaners. Best regards, Tanya

Thank you for your question. We manufacture Delta faucets in our plant facilities in Greensburg, Indiana; Jackson, Tennessee; London, Ontario, CA (and Panyu, China). As a global manufacturer, we also source and assemble a number of parts around the world. No matter where in the world our products are sourced, manufactured or assembled, they are built to Delta Faucet Company’s exacting specifications and are quality tested to ensure long-lasting performance. The location information on the back of the box will tell you where your specific faucet model was made.

Hi, Gary! Thank you for your question. There should be red and blue markings on the supply lines to show hot and cold connections on the Delta 9178-SP-DST Faucet. Best Regards, Rosanna

Hi, Phil52849! Thank you for your question. The Delta 9178-AR-DST Faucet does require a minimum hole size of 1 3/8" (35 mm). Here is a link to the technical specifications sheet for further measurements for the faucet: https://media.deltafaucet.com/SpecSheet/dsp-k-19978-sd-dst_D.pdf Best Regards, Rosanna

Hi Carly, Thank you for your question. The model 9178-RB-DST comes with an aerator with a flow rate of 1.8 gpm. You can order RP53998 which is a 2.2 gpm aerator to raise the flow rate for this particular model. None of our pull down faucets come with a flow rate of 2.2 gpm. Thanks, Dave

Thank you for your question, Jim! I'm sorry to hear you are experiencing a decreased flow and we are happy to help. We would recommend removing the wand to check for debris as well as performing a flush of the faucet. I have emailed you directly about flushing your model. Please refer to that email for further assistance if checking the wand does not help with the flow. Best regards, Edward

Hi, GPH713! Thank you for your question. The handle assembly on the Delta 9178-DST Faucet does need to be centered in order for the faucet to shut off properly. Best Regards, Rosanna

Thank you for your question, Patty! The PVD process we use in the manufacturing of many of our finished products adds the color to our faucets while also providing superior abrasion resistance. We attempt to minimize variations in color by utilizing certain control methods; however, differences in sizes, shapes and materials of individual faucet parts can occasionally produce slight variations in color that are rarely noticeable to the human eye in certain lighting, despite the controls we have in place. Best regards, Edward