Monitor® 14 Series Tub & Shower with In2ition® in Venetian Bronze

Hello Valued Customer, Thank you so much for contacting Delta Faucet Company! The tub spout does not have to be installed with this unit. Please reach out directly with further questions. Best Regards, Kayla

Hi marcy! Thank you for your question and we are happy to help. The 75491 will need to be replaced. Please contact us directly for further assistance. Best Regards, Carrie

Hi LADB, Thank you for your question! Unfortunately, we don't currently carry a bath waste assembly in matte black. I apologize for the inconvenience this causes. Our closest match would be RP693RB in Venetian bronze. Please reach out with any additional questions! Best Regards, Bryan Digital Communications Specialist

Hello Customer! Thank you for your question and we are happy to help. The Delta 144890-SP-I does not have a matching cover plate for a two hole design to single hole. With any further questions or concerns, please do not hesitate to reach out to us again. Best Regards, Carrie

Hi Karen, Thank you for your question about the Delta Faucet model 144890-BL-I. Nonmetallic parts are used to ensure a long-lasting, high-quality product while maintaining safety control for the various temperatures of water that go through the product. With any hand shower, for example, the part of the faucet that you would grab onto is typically made of plastic or a plastic mixture, as metal is heavier, susceptible to corrosion and retains heat. Please contact us directly if you have any additional questions! Best Regards, Bryan Digital Communications Specialist

Hello, Gma3! Thank you for contacting us at Delta Faucet! I apologize for this information not being available to you and I understand how frustrating that can be but I will be happy to help! The hand shower for this Delta Faucet model 144890-I Larkin™ Monitor® 14 Series Tub & Shower With In2ition® In Chrome will pause by switching the mode selector lever to the pause mode, which will reduce the flow rate down to a trickle. Please contact us directly if further assistance is needed at this time.  We appreciate your loyalty to Delta Faucet Company. Best Regards, Tim

Hello Valued Customer, Thank you for your question! We apologize that the information you are searching for was not readily available. We realize that can be very frustrating and I am happy to assist you! We thank you for being a loyal Delta Faucet customer. The Delta Faucet model 144890-BL-I Larkin™ Monitor® 14 Series Tub & Shower With In2ition® In Matte Black can be used as a direct replacement for any Delta Faucet 1300/1400 series or 13/14 MultiChoice (MC) series tub and shower trim. Otherwise, the Delta Faucet model R10000-UNBX MultiChoice® Universal Tub / Shower Rough - Universal Inlets / Outlets will be required for compatibility. Please contact us back directly via email with any further questions. Best Regards, Skyler

Hello, Thank you for your question! There is a diverter switch (not shown in the photo) on the right side of the showerhead that will allow you to switch between showerhead and hand shower. Please reach out with further questions! Best Regards, Tim Digital Communications Specialist

Hello bcart82, Thank you for your question. We are happy to help! A good way to identify if you have a Delta Faucet R10000 MultiChoice valve installed is to look at the valve cartridge. Pre-MultiChoice valves used RP19804, and MultiChoice valves use RP46074. https://www.deltafaucet.com/parts/product/RP19804.html https://www.deltafaucet.com/parts/product/RP46074.html Your cartridge may look a little different, but the top half of the MulitChoice cartridge will be gray and the top half of the pre-MultiChoice cartridge will be white. The legs of the cartridges are also different. Best regards, Bryan

Hello Ashley, Thank you for your question! We apologize that the information you are searching for was not readily available. We realize that can be very frustrating and I am happy to assist you! We thank you for being a loyal Delta Faucet customer. The Delta Faucet model 144890-SP-I Larkin™ Monitor® 14 Series Tub & Shower With In2ition® In Spotshield Brushed Nickel tub spout has an integrated diverter that sits within the body of the spout. There are indents on the sides that show where the finial can be gripped to be pulled up to divert. Please contact us back directly via email with any further questions. Best Regards, Skyler

Hello Janice, Thank you for your question. We are happy to help you adjust your water temperature! The faucet cartridge includes a rotational limit stop to limit how far the handle can turn and the amount of hot water available. Turning it counterclockwise will allow more hot water. Instructions can be found in the faucet manual here: https://media.deltafaucet.com/MandI/107528%20Rev%20C.pdf Please reach out directly if you have any questions or need additional assistance. Best regards, Bryan

Hi Mike, Thanks so much for contacting Delta Faucet Company about your 144890-I! The shower unit can be adjusted, I have attached a link to show how to adjust the RLS on our Delta shower cartridges. This will provide the option of hotter water, also, we recommend making sure the water heater temperature is set to 120 or lower. https://www.youtube.com/watch?v=By5b7uazCqM Please contact us directly if you have any questions or need additional assistance. Best Regards, Nicole Digital Communications Specialist

Hello Teresa, Thank you for your question! I am happy to assist you! The Delta 144890-SP-I is compatible with the included rough in valve and cartridge, as well as the 1300/1400 series RP19804 cartridge and rough in valve. Please contact us back with any further questions. Best Regards, Skyler

Hello Julie, Thank you for your question! I am happy to help you! Our Delta 144890-SP-I will accept our 62"-80" hose U495D-SS60-PK, This is the longest hose we have available that matches your finish. Please contact us back for any further questions. Best Regards, Nicole

Hello Melk, Thank you for contacting us. I am sorry this information is not readily available and I would be happy to help you. The model 144890-BL-I is available to order as of 9/24/2020. Please contact us back if you have any questions or need further assistance.  Best Regards,  Nicole

Hello LAYDAGASI, Thank you for contacting Delta Faucet Company! I am sorry this information was not readily available, and I am happy to help you! Our Delta Faucet LARKIN™ Monitor® 14 Series Tub & Shower With In2ition® MODEL#: 144890-SP-I spout length is 6 5/16", please see the technical specifications below. https://media.deltafaucet.com/SpecSheet/DSP-B-144890-I%20Rev%20B.pdf Thank you for being a loyal Delta customer. Please contact us back for any further questions. Best Regards, Nicole

Hi Carol, Thank you for contacting Delta Faucet Company! Please accept our sincere apology for the inconvenience you are experiencing. We will need more information to better assist you. Please send us an email at customerservice@deltafaucet.com. Best Regards, Skyler

Hi DNolan, Thank you for your question about the Delta Faucet model 144890-I. If the tub spout is installed more than 18" away, it can cause shower rise where water also comes out of the showerhead when the tub spout is used. See here for more information: https://support.deltafaucet.com/s/article/Shower-Rise Please contact us directly if you have any additional questions! Best Regards, Bryan Digital Communications Specialist

Hello annick, Thank you for your question. I apologize for any difficulty finding this information. We are happy to help! The installation and maintenance instructions for the Delta Faucet model 144890-SP-I Larkin tub and shower with In2ition can be found here: https://media.deltafaucet.com/MandI/107528%20Rev%20D.pdf Please reach out with any additional questions. We appreciate your business and look forward to continuing to serve you! Best regards, Bryan

Dear Sarah, Thank you for your question! I will be more than happy to help you! To adjust a 1400 series cartridge, please remove the handle and sleeve. Once these parts are off, you will see a brass stem with a white plastic piece surrounding the brass part. Pull this piece towards you and rotate counter clockwise for hotter water and clockwise for colder water. **Please keep in mind, rotating this could change the temperatures 4-16 degrees farenheight each notch.** Please refer to the link below on page 9, with a # 4 in the black box. https://media.deltafaucet.com/MandI/107528%20Rev%20D.pdf Feel free to contact us directly, if you need further assistance. Best regards, Kyra

Hello Natalie, Thank you for your question on Delta Faucet 144890-SP-I Monitor® 14 Series Tub & Shower With In2ition®, I would be more than happy to assist. We do not recommend using a slide bar for a hand shower on an in2ition showerhead. However, it is compatible with any of our sidebars without a pin mount. Thank you for being a loyal Delta customer. We look forward to better serving you in the future. Please contact us directly with any further questions. Best Regards, Kayla

Hi KerryV, Thank you for contacting Delta Faucet Company! Please accept our sincere apology for the inconvenience you are experiencing. Here is what we can do to resolve your issue for you. Our Delta Faucet Larkin™ Monitor® 14 Series Tub & Shower With In2ition® In Chrome MODEL#: 144890-I has a maximum flow rate of 1.75 GPM @ 80 psi if you are getting lower than the normal flow rate we would recommend flushing the unit. Please see the step-by-step instructions below. To flush the open valve without the cartridge, please follow the directions below. 1) Remove the handle by loosening the set screw on the side of the base of the handle. The set screw is either a 1/8" or 3/32" Allen screw. So you will need to use the appropriate size Allen wrench to loosen it. Loosen it just enough to be able to easily pull the handle off. * Note. If there is calcium build-up at the base of the handle, it may be necessary to soak it in a 50/50 solution of vinegar and water. Simply saturate the rag with the 50/50 solution, wrap it around the handle base and place a plastic bag over it. I would recommend doing this the night before removing the handle. 2) After removing the handle, remove the trim sleeve. 3) Then you will need to remove the bonnet nut. The bonnet nut is the threaded ring at the valve opening. It unscrews counterclockwise. You will need a pipe wrench or a pair of channel locks. 4) After removing the bonnet nut, you will need to pull the cartridge straight out. You may need a small, skinny bladed screwdriver to wedge in between the lip of the cartridge and the valve to help start it out. 5) Once the cartridge is removed, you will have an open valve body. 6) Next, shut the shower door or curtain and turn the water on to the valve. Water should gush out, much like an open fire hydrant. Have someone observe if there is good water pressure coming out of the valve and let it flush for 30 seconds. 7) Re-install the cartridge and re-assemble in reverse of how it was disassembled. The Tub/Shower should then have a good flow. If it does not, the cartridge will need to be replaced. Thank you for being a loyal Delta Faucet customer. We appreciate your business and look forward to continuing to serve you. Please contact us back with any further questions. Best Regards, Nicole

Hello, runchloe! Thank you for contacting us at Delta Faucet! I apologize for this information not being available to you but I will be happy to help! The tub spout with this Delta Faucet 144890-I Larkin™ Monitor® 14 Series Tub & Shower With In2ition® In Chrome is plastic. Please contact us directly if further assistance is needed at this time.  We appreciate your loyalty to Delta Faucet Company. Best Regards, Tim

Hi Allen 23, Thanks for your question regarding 144890-SP-I! The prices on our website are list prices, local or online prices may vary. The price of the item may differ due to collection, finish, and material. All Delta products are manufactured to pass the same quality testing no matter the model number or location of purchase. Please feel free to contact us with any questions or for further assistance. Best Regards, Emma Digital Communications Specialist

Hi Lynne, Thank you for contacting Delta Faucet. Please accept our sincere apology for the inconvenience you are experiencing. We will be happy to assist you in resolving this issue as quickly as possible. Our Delta Faucet Delta LARKIN™ Larkin™ Monitor® 14 Series Tub & Shower With In2ition® In Spotshield Brushed Nickel MODEL#: 144890-SP-I handle is supposed to come on cold first then rotate to hot. If this is happening I recommend having the plumber flip the cartridge. Thank you for being a loyal Delta Faucet customer. Please feel free to call, email, or message us on social if you need anything else. Best Regards, Themar Digital Communications Specialist

Hi mike k, Thank you for contacting Delta Faucet Company! We apologize for the inconvenience you are experiencing and we are happy to help! Our cartridges have a built-in scald protector, and we ship our cartridges already set in the middle range to avoid scalding as water heater temperatures can vary. To fix this, you would need to rotate the "Rotational Limit Stop" on the tip of the cartridge. Please refer to the instructions and the link below! Please refer to page 12 box B: https://media.deltafaucet.com/MandI/107528%20Rev%20G.pdf You shouldn't need to shut your water off but keep in mind it is still possible for the water to turn on if the stem is rotated. Please gather 1/8" allen wrench for a lever handle and a philips screwdriver for a knob handle. 1. Remove your handle with your 1/8" allen wrench. The set screw should be under the lever of the handle. If you have a knob, please remove the cap on the tip of the handle. You will need a philips head screwdriver to remove the screw. 2. Pull the sleeve assembly off of the valve. This is the cylindrical part behind your handle that hides the valve body. 3. You will see a brass stem and a plastic white piece on the tip of the cartridge. The white piece has notches on it to grip it more easily. 4. Please pull the white piece towards you and rotate counter-clockwise for hotter water. *Please note there is a limit of how far this will rotate, if you rotate to the hottest setting it will be the same temperature as your water heater. This is not recommended as it can cause scalding. Please also note that each notch you rotate to can range anywhere between 4 and 16 degrees Fahrenheit.* Now you can install your sleeve and your handle onto your valve. Turn your water on and see if this is your desired temperature. If it is, tighten the set screw or the screw, and the temperature adjustment on the cartridge is done! We appreciate your inquiry. Please reach out directly if you have further questions! Best Regards, Kyra Digital Communications Specialist

Hello Valued Customer, Thank you for contacting Peerless Faucet Company! To tighten the handle on our 144890-SP-I you will need an 1/8" inch allen wrench. We appreciate your inquiry. Please reach out directly if you have further questions! Best Regards, Kyra Digital Communications Specialist

Hi Joseph! Thank you for contacting us at Delta Faucet! I will be happy to help. Unfortunately this does not include the waste/overflow assembly. Best Regards,  ​​​​​​​ Tim

The real answer was that I was missing a part. The spout that came in the box had a 1” diameter threaded opening that would not fit my 1/2 “ threaded pipe. It should have had an adapter with it so I could connect to my 1/2” pipe nipple. Contacted Delta and they are sending the adapter.