Accesorios de ducha Monitor® serie 14 H2Okinetic® en cromado

Hi, Damian! Thank you for your question. The Delta Monitor T14267-BL Shower Trim Kit uses MultiChoice Universal R10000 Rough Valve Body. Unfortunately, we no longer make trim kits with separate volume and temperature control handles. However, our dual pressure balanced Monitor T17267-BL Shower Trim Kit will have volume and temperature control on one control will also use the MultiChoice Universal R10000 Rough Valve Body. Best Regards, Rosanna

Hi Liane, Thank you for your question. From the wall to the furthest point out on the handle is about 3.5 inches. Best regards, Jon

Hi Steve, Thank you for contacting Delta Faucet Company! You shouldn't need to shut your water off but keep in mind it is still possible for the water to turn on if the stem is rotated. Please gather 1/8" allen wrench. 1. Remove your handle with your 1/8" allen wrench. The set screw should be under the lever of the handle. 2. Pull the sleeve assembly off of the valve. This is the cylindrical part behind your handle that hides the valve body. 3. You will see a brass stem and a plastic white piece on the tip of the cartridge. The white piece has notches on it to grip it more easily. 4. Pull the white piece towards you and rotate counter-clockwise for hotter water. *Please note there is a limit of how far this will rotate, if you rotate to the hottest setting it will be the same temperature as your water heater. This is not recommended as it can cause scalding. Please also note that each notch you rotate to can range anywhere between 4 and 16 degrees Fahrenheit.* Now you can install your sleeve and your handle onto your valve. Turn your water on and see if this is your desired temperature. If it is, tighten the set screw or the screw, and the temperature adjustment on the cartridge is done! We appreciate your inquiry. Please reach out directly if you have further questions! Best Regards, Kyra Digital Engagement Specialist

Hi lam lam, Thank you for contacting us at Delta Faucet! We apologize for any inconvenience this may have caused but are happy to help. Please see the following link for for a How-To video on resolving this. https://www.youtube.com/watch?v=L3ty-H1V01I&t=130s Please contact us directly if further assistance is needed at this time.   Best Regards, Tim Digital Communications Specialist (800) 345-3358 customerservice@deltafaucet.com

Hello Suzi, Thank you for your question! We apologize that this information was not readily available and will be happy to help you. The Delta Faucet Ara® Monitor® 14 Series H2Okinetic® Shower Trim In Chrome MODEL#: T14267 is made of several materials, and includes metallic and non-metallic parts. Non-metallic products are beneficial in that they do not rust or corrode and help prevent heat transfer. We also have a Lifetime Limited Warranty on all parts and finish. Allowing water to evaporate on the surface can lead to the build-up of mineral deposits, and we recommend blotting the faucet dry after use to prevent this from happening. However, water spots and fingerprints can be easily cleaned by wiping the finish with a damp cloth. If additional cleaning is needed, we recommend using a 50/50 solution of white vinegar and water Thank you for being a loyal Delta Faucet customer. We look forward to continuing to serve you. Please feel free to contact us back for further assistance. Best Regards, Kelley

Hello Marcy, Thank you for your question! We apologize that the information you are searching for was not readily available. We realize that can be very frustrating and I am happy to assist you! We thank you for being a loyal Delta Faucet customer. The Delta Faucet model T14267-BL Ara® Monitor® 14 Series H2Okinetic® Shower Trim In Matte Black will require a 3-way shower arm diverter or a separate Delta Faucet model R11000 3- And 6-Setting Diverter Rough and corresponding diverter trim to allow use with a hand shower. Please contact us back directly via email with any further questions. Best Regards, Skyler

Hello Wyatt, Thank you for contacting Delta Faucet Company! I am sorry this information was not readily available for our Delta Faucet ARA® Ara® Monitor® 14 Series H2Okinetic® Shower Trim In Matte Black MODEL#: T14267-BL, and I am happy to help you! I have attached a link to show how to adjust the RLS on our Delta shower cartridges. This will provide the option of hotter water, also we recommend making sure the water heater temperature is set to 120 or lower. https://www.youtube.com/watch?v=By5b7uazCqM Also, low flow is caused by a blockage or debris, we would recommend flushing the shower unit to increase the flow. To flush the open valve without the cartridge, please follow the directions below. 1) Remove the handle by loosening the set screw on the side of the base of the handle. The set screw is either a 1/8" or 3/32" Allen screw. So you will need to use the appropriate size Allen wrench to loosen it. Loosen it just enough to be able to easily pull the handle off. * Note. If there is calcium build-up at the base of the handle, it may be necessary to soak it in a 50/50 solution of vinegar and water. Simply saturate the rag with the 50/50 solution, wrap it around the handle base and place a plastic bag over it. I would recommend do this the night before removing the handle. 2) After removing the handle, remove the trim sleeve. 3) Then you will need to remove the bonnet nut. The bonnet nut is the threaded ring at the valve opening. It unscrews counterclockwise. You will need a pipe wrench or a pair of channel locks. 4) After removing the bonnet nut, you will need to pull the cartridge straight out. You may need a small, skinny bladed screwdriver to wedge in between the lip of the cartridge and the valve to help start it out. 5) Once the cartridge is removed, you will have an open valve body. 6) Next, shut the shower door or curtain and turn the water on to the valve. Water should gush out much like an open fire hydrant. Have someone observe if there is good water pressure coming out of the valve and let it flush for 30 seconds. 7) Re-install the cartridge and re-assemble in reverse of how it was disassembled. The Tub/Shower should then have a good flow. If it does not, the cartridge will need to be replaced. Thank you for being a loyal Delta Faucet customer. Please contact us back with any further questions. Best Regards, Nicole

Hi Rozy, thank you for contacting Delta Faucet Company! The difference between our T14 and our T17 series shower valves is listed below. T14 - one single handle that will adjust for temperature and volume. T17 - Two handles on the same valve. The large handle will adjust for volume and the small handle will adjust for temperature. It is normal for the temperature to turn with the volume so you can keep the same temperature as previously used. We appreciate your inquiry. Please reach out directly if you have further questions! Best Regards, Kyra Digital Communications Specialist