Conjunto interior universal MultiChoice® para bañera/ducha, entradas/salidas universales

Hi, James! Thank you for your question. The R10000-UNWS will work with any of our Delta trim that available now. The new trim kits will come with the cartridge needed to complete your faucet. Here is a link to our Delta shower trim kits that are available: https://www.deltafaucet.com/bathroom/showering/tub-and-shower-faucets Best Regards, Rosanna

Hello Marv, Thank you for your inquiry! When installing a tub spout, the drop from the bottom port of the valve must be 1/2" copper or 1/2" galvanized pipe as the internal diameter of the pipe is important to prevent back-pressure. Best regards, Tanya

Hi, Thank you for contacting us. We apologize for any inconvenience. We are more than happy to help you. The MultiChoice® Universal Tub/Shower Rough is a Universal Inlets/Outlets. It accepts single, dual, or dual thermostatic cartridges. Cartridges do come with the trim kits. Please contact us at 1-800-345-3358 if you have any further concerns. We are open Monday through Friday 7:00 AM to 7:00 PM central time, and 8:00 AM to 5:00 PM on Saturday. Best Regards, Bethany

Hi Robin, Thank you for your question. The only extension kit available for the R10000-UNWS works if you are using a 17 series thermostatic trim. The part number is RP75136. If you are using a T13, T14, or a T17 series pressure balanced trim, there is no extension kit available that will work with the R10000-UNWS. Thanks, Dave

Hi, Ducky! Thank you for your question. There is no difference between the Delta MultiChoice Universal R10000-UNWS-3 rough-in valve body with stops and the Delta MultiChoice Universal R10000-UNWS rough-in valve body with stops. The "-3" in the model number indicates the unit is exclusive to The Home Depot. The make and quality is the exact same. Best Regards, Rosanna

Hi, Lynnett! Thank you for your question. Any of our Delta Faucet Trim Kits fit our Delta MultiChoice Universal R10000-UNWS-3 Rough In Valve Body. Here is a link to our trim kits: https://www.deltafaucet.com/bathroom/showering/tub-and-shower-faucets Best Regards, Rosanna

Hello Andy, Thank you for your question. Unfortunately, the Delta MultiChoice Universal R10000-UNWS-3 Rough In Valve Body and tub spout must be installed between 8"-18" to prevent Shower Rise. Best regards, Tanya

Thank you for your question, MIKE J! The R10000-UNWS and R10000-UNWS-3 are the same valve body. The only difference is that the R10000-UNWS-3 comes included with 3 R10000-UNWS valve bodies. Best Regards, Benjamin

Hi JB! Thank you for your question. We recommend using proper fittings with each type of Multichoice Universal Rough Valve (copper tubing, iron pipe, and pex fitting). Below is a link with more information on these valves. https://media.deltafaucet.com/SpecSheet/DSP-B-R10000%20Rev%20J.pdf Best regards, Edward

Hi aromaniz, Thank you for your question! Our tub and shower faucets can operate between 30 and 100 PSI. Best regards, Jon

Thank you for your question, Lowes 2302! The two models are functionally the same model, only the packaging is different. The R10000-LBX is packaged exclusively for Lowe's Home Improvement stores. Best Regards, Benjamin

Hi, Casey! Thank you for your question. The Delta MultiChoice Universal rough valve bodies R10000-UNBX and R10000-UN are the same and have no differences. For a 3 neck hook-up, we recommend to add a diverter valve to the top port to be able to install additional shower units. Best Regards, Rosanna

Hi, Asn86! Thank you for your question. The Delta MultiChoice Universal Tub / Shower Rough - Universal Inlets / Outlets (R10000-UNBX) is only guaranteed to work with Delta Valve Trim kits. Best Regards, Rosanna

Hi Jumperboy, Thank you for your question. While the tub spout would work, the thermostatic cartridge RP47201 would not work with the handles for the T17253. You would also need the RP62960 volume handle, RP62959 temperature knob, and RP50879 sleeve. http://www.deltafaucet.com/search/results.html?q=RP62960%2C+RP62959%2C+RP50879+ Thanks, Jon

Hi, Renmarq! Thank you for your question. You are correct, the hot should be on the left side. The cold should be towards the right side. Best Regards, Rosanna

Hi Joe, We are sorry that you are experiencing a problem with your faucet. Most likely, you are experiencing "shower-rise" where the water can’t get out of the spout as fast as it flows through the valve. This causes the water to back up and come out the shower head. There can be one of several reasons for this: The valve could be upside down The length from the valve to the tub spout is outside of the 8" to 18" rule There is more than one 90-degree angle Something other than copper or galvanized pipe was used going to the spout The most common reason is that there is something restricting the water flow to the spout, e.g. solder or something lodged in the pipe. Something is impeding the flow of water to the spout and causing it to back up and go out the shower head. If this is the cause of shower-rise it is possible to remove the blockage by removing the tub spout; then, feeding a plumber’s snake or a speedometer cable up through the tub drop. The act of feeding it causes it to twirl and loosen the blockage. Be sure to flush the valve before reinstalling the tub spout. Be sure to check the tub spout itself for blockage. If none of these help, you may need to call a plumber. After the shower has been installed and the wall has been closed, there is little that can be done to remedy this situation yourself. Read more: http://www.deltafaucet.com/customersupport/faq/showers/index.html#ixzz2kj330m5y Thanks, Dave

Hi, Eric! Thank you for your question. The hot and cold water supplies can be reversed from the Delta MultiChoice Universal R10000-UNBXT Rough Valve Body. Best Regards, Rosanna

Dear Garies, Thank you for your question. The Delta MultiChoice Rough-In R10000-UNBX Valve is recommended to used T17264 (shower only) or the T17464 (tub/shower). The Delta Diverter R11000 Valve would be installed above it. Best Regards, Tanya

Thank you for your question, Karen. The R10000-UNBX valve is the highest flow rate for the tub spout. The actual flow rate will depend on the water pressure in the home and the trim series that you install. Here are the flow rates from this valve (tub spout port) at 60 PSI: 14 Series: 6.0 GPM 17 Series: 6.2 GPM 17T Series: 7.8 GPM Best regards. Jon

Hi, Ed! Thank you for your question. All of our Delta MultiChoice R10000 Rough In Valve Bodies work with any of our Delta Single and Dual Monitor and TempAssure Valve Trim Kits. Cartridge are included with each trim kit. Here is a link to our trim kits: https://www.deltafaucet.com/bathroom/showering/tub-and-shower-faucets Best Regards, Rosanna

Hi, Edward! Thank you for your question. The Delta MultiChoice R10000-UNBX rough in valve will not determine the flow rate. The trim kit that is selected to be installed with the rough in valve will include the valve cartridge assembly and will determine the flow rate for the unit. Best Regards, Rosanna

Thank you for your question, Erio! The Delta MultiChoice Universal Rough-In Valve R1000-UNBX is currently the only shower and tub/shower valve we manufacture. The ASSE1016MASCO is a plumbing code printed on several of our showering parts. Best regards, Tanya

Hi Sky, Thank you for your question! Please make sure that the plaster guard is flush (or up to 3/8" sub flush) with the finished wall. If the valve is out too far, you may turn the stops 3 turns in from the full open position without a noticeable reduction of flow. This will provide an additional 1/8” of clearance for the escutcheon. Best regards, Jon

Thank you for your question. Based on your picture, your model is a 1300/1400 series faucet and the cartridge is a model RP19804.

Thank you for your question, Rivermn. This valve is about 4" wide and will require supplies on the hot and cold side. You will need enough room for the plumbing connections and or elbows. Here is a link to the instructions for more information: https://media.deltafaucet.com/MandI/50353%20Rev%20J.pdf Best regards, Jon

Hi Doug, Thank you for your question! The hole for the valve should be cut to the size of the plaster guard which is 4" x 4". The hole for the size of the tub spout should be at least 1/2" for the pipe to fit through and no larger than the diameter of the tub spout, which is 3 1/8" on this model. Valve specs - http://www.deltafaucet.com/customersupport/documentation/r10000-unbx.html?document=ts&fromDetailArea=bath&documentIndex=0#flashWrapper Trim kit specs - http://www.deltafaucet.com/customersupport/documentation/1755rb-716rb.html?document=ts&fromDetailArea=bath&documentIndex=0#flashWrapper Best Regards, Daniel

Thank you for your question, Batcave! The R10000-UNBX MultiChoice Universal valve does not control temperature but rather acts as a simple mixing valve. The pressure balanced 13/14/17 series cartridges as well as the T17T trims which include a TempAssure Thermostatic cartridge will keep the temperature between ±3° F (±1.6° C) at all times. Best regards, Edward

Hi Jayesh, Thank you for your question. Unfortunately, R10000-UNBX is not compatible with a sink faucet. Best Regards, Courtney

Hi Iku1, Thank you for your question. The motion of the handle will run from 3 o-clock (off) to 12 o-clock (full on). The faucet is equipped with a rotational limit stop where you set how hot the water can get. I have attached a link to a video to show you how to make this adjustment. Thanks, Dave http://www.deltafaucet.com/shopping-tools/research/video-gallery/video.html?v=n2_uZ7wgV1I&cat=

Thank you for your question. Delta Faucet model R10000-UNBX can be used for a shower only application by pluggin the tub port. Model number R10000-UNBXHF is for shower only applications and if you would like higher flow from your valve. If you already have the R10000-UNBX, you can use it for a shower only application.