Conjunto interior universal MultiChoice® para tina/ducha - Entradas/salidas universales

Hi Jumperboy, Thank you for your question. While the tub spout would work, the thermostatic cartridge RP47201 would not work with the handles for the T17253. You would also need the RP62960 volume handle, RP62959 temperature knob, and RP50879 sleeve. http://www.deltafaucet.com/search/results.html?q=RP62960%2C+RP62959%2C+RP50879+ Thanks, Jon

Hi Joe, We are sorry that you are experiencing a problem with your faucet. Most likely, you are experiencing "shower-rise" where the water can’t get out of the spout as fast as it flows through the valve. This causes the water to back up and come out the shower head. There can be one of several reasons for this: The valve could be upside down The length from the valve to the tub spout is outside of the 8" to 18" rule There is more than one 90-degree angle Something other than copper or galvanized pipe was used going to the spout The most common reason is that there is something restricting the water flow to the spout, e.g. solder or something lodged in the pipe. Something is impeding the flow of water to the spout and causing it to back up and go out the shower head. If this is the cause of shower-rise it is possible to remove the blockage by removing the tub spout; then, feeding a plumber’s snake or a speedometer cable up through the tub drop. The act of feeding it causes it to twirl and loosen the blockage. Be sure to flush the valve before reinstalling the tub spout. Be sure to check the tub spout itself for blockage. If none of these help, you may need to call a plumber. After the shower has been installed and the wall has been closed, there is little that can be done to remedy this situation yourself. Read more: http://www.deltafaucet.com/customersupport/faq/showers/index.html#ixzz2kj330m5y Thanks, Dave

Hi Sky, Thank you for your question! Please make sure that the plaster guard is flush (or up to 3/8" sub flush) with the finished wall. If the valve is out too far, you may turn the stops 3 turns in from the full open position without a noticeable reduction of flow. This will provide an additional 1/8” of clearance for the escutcheon. Best regards, Jon

Hi Iku1, Thank you for your question. The motion of the handle will run from 3 o-clock (off) to 12 o-clock (full on). The faucet is equipped with a rotational limit stop where you set how hot the water can get. I have attached a link to a video to show you how to make this adjustment. Thanks, Dave http://www.deltafaucet.com/shopping-tools/research/video-gallery/video.html?v=n2_uZ7wgV1I&cat=

Thank you for your question, A.Luna! The screw driver stops are included with the valve. Best regards, Jon

Hello, Thank you for your question. We are happy to assist you. To better assist you, Please contact us at 1-800-345-3358. We are open Monday through Friday 7:00 AM to 7:00 PM central time, and 8:00 AM to 5:00 PM on Saturday. Thank you for your cooperation. Best Regards, Bethany

Hi, Linda! Thank you for your question. The Delta MultiChoice Universal R10000-UNWS rough valve body works with any of our Delta 13/14, 17, and 17T series trim kits. We cannot guarantee that they will fit with other brand trim kits. The valve body does work with both shower head and tub spout installations. Best Regards, Rosanna

Thank you for your question Wei! RP46074 is the correct cartridge for the Multichoice R10000-UNWS valve and the plasterguard should be flush or subflush 1/4" to the finished wall according to the installation manual. Distance from the stringer to the front of the plasterguard is 2-3/4" ± 1/4" (70 mm ± 6 mm). Distance from the stringer to the front of the bonnet is intended to be 3 7/8" (99 mm.) This is for reference only. If you need further assistance with this installation you can call us directly at 1-800-345-3358. Best regards, Edward