Llave para barra/preparación de alimentos extensible de una manija en cromado

Hi, Hiker! Thank you for your question. The Delta 9959-DST faucet at 40 PSI will give a 1.3 gpm flow rate. Best Regards, Rosanna

Hi, SFDave! Thank you for your question. The Voice Module can be purchased separately as part number EP100021. https://www.deltafaucet.com/kitchen/product/EP100021 Faucets with a Gen3L solenoid assembly are compatible for use with the Voice Module. Older incompatible solenoid assemblies are grey/silver while the compatible solenoid assemblies are all black. Please note that an Amazon Alexa-enabled device is required in order to use voice-activation. Please click the link below for more information about this feature. https://www.deltafaucet.com/Voice Best Regards, Rosanna

Thank you for your inquiry, David! The sprayer/wand assembly of the Delta Trinsic Pull-Down Kitchen 9159-DST faucet is non metallic and it operates in an aerated or spray mode via ergonomic buttons. Best regards, Tanya

Hi, Aaron! Thank you for your question. We do not have Delta Trinsic faucet that does not have pull down sprayer assembly. We also do not have sprayer assemblies that have just the stream mode option. Best Regards, Rosanna

Hi, Akko! Thank you for your question. We do not recommend to install a water filter to the Delta 9159-AR-DST Faucet sprayer assembly, as potential pressure fluctuations during water filter operation may result in the hose rupturing. Best Regards, Rosanna

Hi, wbcIII! Thank you for your question. The Delta 9159-BL-DST faucet may not be shipped to Brooklyn, NY 11237 as it has a flow rate of 1.80 GPM @ 60 PSI. The maximum flow rate to be within the NYC Green Code is 1.5 GPM @ 60PSI. Best Regards, Rosanna

Hi there Becca, Thank you for your inquiry! A comprehensive list of cleaners is impossible to recommend because of the variety of materials that are a part of our many models of faucets. What may be fine for a spout may damage a handle. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel. Stubborn hard water spots are best avoided by this daily regime. If extra measure is needed, a solution of 50% white vinegar (never Apple vinegar) could be used by wiping, spraying or soaking. Caution: Vinegar can permanently damage porous rock surfaces such as granite or limestone countertops. Use extreme care if such a surface is in the vicinity. To soak a faucet or part still on a faucet: 1. Mix white vinegar and tap water to a half and half proportion. 2. Put a rag or towel in the solution to soak it up. 3. Wrap the rag or towel around the part. 4. Let sit for up to an hour or so. 5. Use the rag or a clean, soft toothbrush to scrub the remaining hard water buildup. o Avoid harsh abrasives or polish o Avoid bleach-based cleaners o Avoid industrial cleaners and abrasive cleaners, such as those used for toilet bowls, green Scotch-Brite heavy duty scrub sponges, Scrubbing Bubbles Bathroom Cleaner and Lysol Basin Tub, Soft Scrub, and Tile Cleaner. o Avoid products that state on the label that they remove tarnish and rust, and those containing hydrofluoric, hydrochloric and/or phosphoric acids and caustic agents. o Because cleaning formulas can change without notice, Delta Faucet Company does not endorse any specific cleaner. Best regards, Tanya

Hi Gary, Thank you for your question. The model 9159-AR-DST does have an aerator that is part of the wand assembly that controls the flow of water when the faucet is in stream mode. Thanks, Dave

Hi, Thank you for contacting us. We apologize for any inconvenience. We are more than happy to help you. Reduced flow or no flow is typically caused by debris. If only one side is affected, there is debris in the supply line. To flush the supply line, first shut off the hot and cold water supply. Remove the hot supply line from the shut off valve and place the line into a bucket. Open the handle to the middle position, then fully open, then turn the cold supply back on for one minute. The cold water should flow through the faucet and out the hot supply tube. Reconnect the supply line and turn on both supplies. Check flow from the faucet. If this does not help, please let us know. Please contact us at 1-800-345-3358 if you have any further concerns. We are open Monday through Friday 7:00 AM to 7:00 PM central time, and 8:00 AM to 5:00 PM on Saturday. Best Regards, Bethany

Hello, pamdem. Thank you for you for your question! The RP64070 Escutcheon Plate will work with this faucet for a 3-hole 8" installation. Otherwise, you may also use a soap/lotion dispenser such as the RP1001 or the RP3816 Hole Cover. RP64070 https://www.deltafaucet.com/parts-product-detail?modelNumber=RP64070 RP1001 https://www.deltafaucet.com/parts-product-detail?modelNumber=RP1001 Best regards, Jon

Hi Diana, Thank you for your question. The recommended hole size for the model 9959-DST and 9159-DST faucets is 1-1/4" to 1-1/2". Either faucet should fit your 1-1/4" hole. Thanks, Dave

Hi, AND Portland! Thank you for your question. Unfortunately, we do not have a lower gpm aerator to reduce the flow for this 9159-DST faucet. Best Regards, Rosanna

Hi, Cheshire! Thank you for your question. The Delta 9159-DST faucet has minimum clearance to back splash of 2 1/2" (64 mm). Best Regards, Rosanna

Hi Meg, Thank you for your question! The model 9959-DST is CSA certified. Below is the link to the technical specification for the unit. This provides information on what codes it complies with. http://www.deltafaucet.com/customersupport/documentation/9159-ar-dst.html?document=ts&fromDetailArea=kitchen&documentIndex=0#flashWrapper Best regards, Brandis

Hi Ron, Thank you for your question! With the faucet installed with the handle facing the right the handle will rotate forward. Pulling the handle out will turn the unit on and put out cold water and when the handle is pulled forward you will get hot water. Best regards, Brandis

Thank you for your question. The Delta Trinsic Pull-Down Kitchen 9159-DST faucet has a flow rate of 1.8 GPM at 60 PSI, this flow is not designed to be reduced. The three Delta Kitchen Pull-Out/Down faucets with a 1.5 GPM at 60 PSI are models 9192-DST, 4153-DST and 4353-DST. https://media.deltafaucet.com/SpecSheet/DSP-K-19992-SD-DST%20Rev%20B.pdf https://media.deltafaucet.com/SpecSheet/DSP-K-4153-DST%20Rev%20C.pdf https://media.deltafaucet.com/SpecSheet/DSP-K-4353-SD-DST%20Rev%20B.pdf Best regards. Tanya

Hello Ron H, Thank you for your question. The Delta Trinsic Pull-Down Kitchen 9159-DST faucet has a flow rate of 1.8 GPM at 60 PSI, this is the highest flow rate that we manufacture for our Delta kitchen faucets. Best regards, Tanya

Hi HarryWent, Thank you for your question. Please refer to the Technical Specifications linked below. The maximum deck thickness with the 3 hole escutcheon plate is 2.5". The maximum deck thickness without the escutcheon plate is 3". https://media.deltafaucet.com/SpecSheet/DSP-K-9159-DST%20Rev%20E.pdf Best regards, Jon

Hi, Miriam! Thank you for your question. We do recommend to contact our International Department via email at intlservices@deltafaucet.com to inquire if this faucet is available in Ireland or the UK. Best Regards, Rosanna

Hi, LeftMount! Thank you for your question. The Delta 9959-DST faucet can be installed with the handle mounted to the left as the spout does rotate 360 degrees. However, be aware that the operation of the handle will be opposite. Best Regards, Rosanna

Thank you for your question, KHill09! The RP62057 hose provided with model 9159-DST is 62". Best regards, Edward

Hello Monicat, Thank you for your question. All our finishes will have a protective coating to help the finish last a lifetime. We recommend specific cleaning and care instructions in order to keep this faucet look new for a long as possible. https://www.deltafaucet.com/design-innovation/inspiredliving/how-to-clean-a-faucet Best regards, Tanya

Thank you for your question, David. Our Lifetime Limited Warranty applies to faucets installed in the United States of America, Canada and Mexico. We do not send warranty parts to other countries. Best regards, Jon

Hi, Ellen! Thank you for your question. The Delta 9159-AR-DST Faucet handle turns out, away from the faucet body, for cold water, and towards the user for hot water. Best Regards, Rosanna

Hello Dell, Thank you for your question! This faucet is available in Arctic Stainless, Champagne Bronze, Chrome, and Black. Please click the link below to view products currently available in the SpotShield Stainless finish: https://www.deltafaucet.com/kitchen/sink-faucets?facetFinish=spotshieldstainless Best regards, Jon

Thank you for your question, Jeanie! We recommend unscrewing the wand assembly from the hose and soaking it in a 50/50 white vinegar and water solution for about 30-60 minutes, then run water both directions through the wand. You can also use an old toothbrush to gently scrub the aerator. Please be sure that the hose does not retract into the spout with the wand removed. Best regards, Jon

Thank you for your question. Delta Faucet model # 9959-CS-DST does have separate hot and cold water supply lines for the the faucet.

Hi, Meliss. Thanks for your question! We recommend a hole size of 1 1/4" to 1 1/2". Please refer to the Technical Specifications: https://media.deltafaucet.com/SpecSheet/DSP-K-9159-DST%20Rev%20E.pdf Best regards, Jon

Hello Valerie, Thank you for your question. There are no lead containing components used in the construction of the Delta Trinsic Kitchen Pull-Out 9159-DST faucet or any of our DST (Diamond Seal Technology) and LF (Lead Free) faucets. Delta Certifies products with a third-party certifier, CSA Group, to the ASME A112.18.1/CSA B125.1, Plumbing Supply Fittings. To be in compliance with ASME A112.18.1/CSA B125.1 Section 4.9.1 (excerpt below), the model is required to be in compliance with the applicable section of NSF 61. 4.9 Toxicity and lead content 4.9.1 Fittings covered by this Standard shall comply with the applicable requirements of NSF/ANSI 61. 4.9.2 Solders and fluxes in contact with potable water shall not exceed, by mass, 0.2% lead content. Metal alloys in contact with potable water shall not exceed 8% lead content. 4.9.3 Fittings intended to convey or dispense water for human consumption through drinking or cooking shall not contain a weighted average lead content in excess of 0.25% when evaluated in accordance with the test method specified in NSF/ANSI 372. The product compliance listing can be found online, see link below. http://www.csagroup.org/services/testing-and-certification/certified-product-listing Best regards, Tanya

Hi Brenda, Thank you for your question! This model is 15 11/16″ tall. Technical Specifications: http://www.deltafaucet.com/customersupport/documentation/9159-bl-dst.html?document=ts&fromDetailArea=kitchen&documentIndex=0#flashWrapper Best regards, Jon